Glossary

Below are terms and definitions that we often use, for easier searching options choose a letter below:

A   B   C   D   E    F   H    L   M   O    P   R   S    T   U    V   Z

 

Glossary of HVAC/R Terms: A

AFUE - Annual Fuel Utilization Efficiency

Indicated as a percentage, your furnace's AFUE tells you how much energy is being converted to heat. For example, an AFUE of 90 means that 90% of the fuel is being used to warm your home, while the other 10% escapes as exhaust with the combustion gases.

Air Handler

Fan blower, filter and housing parts of a system.

ARI - Air Conditioning and Refrigeration Institute

A non-profit, voluntary organization comprised of manufacturers of air conditioning, refrigeration, and heating products. It publishes standards for testing and rating heat pumps and air conditioners. The information provides the consumer with a standardized unit of comparison between equipment from various manufacturers and ensures a level of quality within the industry.

Back to Top

Glossary of HVAC/R Terms: B

BTU - British Thermal Unit

Is used for both heating and cooling, BTU is a measure of heat given off when fuel in combusted. Or for cooling, its a measure of heat extracted from your home. One BTU is equal to the heat given off by a wooden kitchen match.

BTUH

Btu's per hour.

Back to Top

Glossary of HVAC/R Terms: C

CFC Certification

Chlorofluorocarbon, a compound consisting of Chorine, Fluorine, and Carbon. Technicians who repair or service R-12 or R-134a refrigerant must be trained and certified by an EPA-approved organization. Training programs must include information on the proper use of equipment, the regulatory requirements, the importance of refrigerant recovery, and the effects of ozone depletion. To be certified, technicians must pass a test demonstrating their knowledge in these areas.

CFM - Cubic Feet per Minute

A measurement of airflow that indicates how many cubic feet of air pass by a stationary point in one minute. The higher the number, the more air is being forced through the system.

Capacity

The ability of a heating or cooling system to heat or cool a given amount of space. For heating, this is usually expressed in BTU's. For cooling, it is usually given in tons.

Carbon Monoxide

A colorless, odorless highly poisonous gas produced when carbon-based fuels, such as natural gas, burns without sufficient air nearby.

Charge

Amount of refrigeration placed in a refrigerating unit (air conditioner).

Compressor

Part of a split system heat pump or air conditioner's outdoor unit that controls the pressure applied to the refrigerant, necessary for taking heat to warm your home or getting rid of heat to keep your home cool.

Condensation

Formed by more heating being absorbed into the air leaving less temperature to carry the water vapor produced in gas combustion to pass out of the venting system.

Condenser Coil

Part of the outdoor portion of a split system air conditioner or heat pump. By converting refrigerant that is in a gas form back to a liquid, the coil sends heat carried by the refrigerant to the outside.

Back to Top

Glossary of HVAC/R Terms: D

Damper

A device that is located in ductwork to adjust airflow. This movable plate opens and closes to control airflow to certain rooms of your home.

Decibel (db)

Decibels (db) are a unit measuring the intensity of noise.

Direct Vent

Pulls outside air for combustion and vents combustion gases directly outside.

DOE - Department Of Energy

Department of Energy is the Federal agency in charge of monitoring the consumption of energy sources.

Downflow

A type of furnace that takes cool air from the top and blows warm air to the bottom - common where furnaces must be located in a second-floor closet or utility area.

Dual-Fuel

See Hybrid Heat

Ductwork

Hollow pipes used to transfer air from the Air Handler to the air vents throughout your home. Ductwork is one of the most important components of a home heating and cooling system.

Back to Top

Glossary of HVAC/R Terms: E

Electronic Air Cleaner

An electronic device that filters out large particles and contaminants in indoor air. It then electronically pulls out tiny particles that have been magnetized, such as viruses and bacteria, drawing them to a collector plate.

Evaporator Coil

Part of split system air conditioner or heat pump indoors. The evaporator coil cools and dehumidifies the air by converting liquid refrigerant into a gas, which absorbs the heat from the air. The warmed refrigerant is then carried through a tube to the outdoor unit.

Glossary of HVAC/R Terms: F

Fan Coil

An indoor component of a heat pump system, used in place of a furnace, to provide additional heating on cold days when the heat pump does not provide adequate heating.

Back to Top

Glossary of HVAC/R Terms: H

HVAC

Term used for Heating, Ventilation, and Air Conditioning.

HSPF - The Heating Seasonal Performance Factor

The Heating Seasonal Performance Factor is a measure of the heating efficiency of a heat pump. The higher the HSPF number, the more efficiently the heat pump heats your home.

Heat Exchanger

The part of a furnace that transfers heat to nearby air.

Heat Pump

A product that works just like an air conditioner is cooling mode; however, in heating mode, the refrigerant flow is reversed and heat is extracted from the outside air to heat your home

Horizontal Flow

A type of furnace, installed on its "side", that draws in the air from one side, heats it, and sends the warm air out the other side. Most often used used for installations in attics or crawl spaces.

Humidifier

A piece of equipment that adds water vapor to heated air as it moves out of the furnace. This adds necessary moisture to protect your furnishings and reduce static electricity.

Hybrid Heat

A Hybrid Heat system is a fuel-saving alternative to traditional heating and cooling systems that combines a furnace with a heat pump, rather than an air conditioner.

Back to Top

Glossary of HVAC/R Terms: L

Load Estimate

A series of studies performed to determine the heating or cooling requirements of your home. An energy load analysis uses information such as the square footage of your home, window or door areas, insulation quality, and local climate to determine the heating and cooling capacity needed by your furnace, heat pump, or air conditioner. When referring to heating, this is often known as Heat Loss Analysis, since a home's heating requirements are determined by the amount of heat lost through the roof, entryways, and walls.

Back to Top

Glossary of HVAC/R Terms: M

Matched System

A heating and cooling system comprised of products that have been certified to perform at promised comfort and efficiency when used together, and used according to design and engineering specifications.

Back to Top

Glossary of HVAC/R Terms: O

Operating Cost

The day-to-day cost of running your home comfort equipment, based on energy use.

Outdoor Unit

Refrigerant containing portion of a fan coil unit similar to a car radiator, typically made of several rows of copper tubing with aluminum fins.

Back to Top

Glossary of HVAC/R Terms: P

Payback Analysis

Overall measure of the efficiency and value of your home comfort system. By combining your purchase price and ongoing operating costs, a payback analysis determines the number of years required before monthly energy savings offset the purchase price.

Puron (carrier Only)

PPuro refrigerant is an environmentally sound refrigerant designed not to harm the earth's ozone layer. Federal law requires that all manufacturers phase out ozone depleting refrigerants in the next few years. Puron is approved by the US Environmental Protection Agency as a replacement for Freon R22. See Puron vs. R-22 R22 R22 is a single component HCFC refrigerant with low ozone depletion potential. It has long been used in a variety of air conditioning and refrigerant applications in a variety of markets. Production of R22 will cease in 2015 per the Montreal Protocol.

Back to Top

Glossary of HVAC/R Terms: R

Reclaim

Returning used refrigerant to the manufacturer for disposal or reuse.

Refrigerant

Substance used in refrigerating mechanism. It absorbs heat by changing from a liquid to a gas, and releases its heat in a condenser as the substance returns from the gaseous state back to liquid state.

Register

Combination grill and damper assembly covering an air opening or end of an air duct.

Return Air

Air drawn into a heating unit after having been circulated from the heater's output supply to a room.

Back to Top

Glossary of HVAC/R Terms: S

Seer

The Seasonal Energy Efficiency Ratio is a measure of the cooling efficiency of your air conditioner or heat pump. The higher the SEER number, the more efficient the system is at converting electricity into cooling power.

Scroll Compressor

A specially designed compressor that works in a circular motion vs. an up and down piston action.

Split System

Refers to an air conditioner or heat pump that has components in two locations. Usually, one part of the system is located inside (evaporator coil) and the other is located outside (condenser coil).

Back to Top

Glossary of HVAC/R Terms: T

Therm

A measurement of 100,000 BTU's.

Thermidistat

The Thermidistat Control monitors temperatures both inside and outside, as well as indoor humidity and adjusts system operation to maintain the temperature and humidity levels set by the Homeowner.

Thermostat

Unit that monitors and controls your HVAC system products.

Ton

A unit of measurement for cooling capacity. One ton = 12,000 BTU's per hour.

Back to Top

Glossary of HVAC/R Terms: U

Upflow

A type of furnace that draws cool air from the bottom and blows the warmed air out the top into the ductwork. This type of furnace is usually installed in a basement or an out-of-the-way closet.

Back to Top

Glossary of HVAC/R Terms: V

Ventilator

A ventilator captures heating or cooling energy from stale indoor air and transfers it to fresh incoming air.

Back to Top

Glossary of HVAC/R Terms: Z

Zoning

A way to increase your home comfort and energy efficiency by controlling when and where heating and cooling occurs in a home. Programmable thermostats are used to control operating times of the equipment. Dampers are used to direct airflow to certain parts or "zones" of the home.

Back to Top

Contact Taylor's for all your HVAC Needs

There is more to a heating and air conditioning system than its ratings. The quality of the construction and materials used as well as the reliability of the manufacturer and installing contractor can all affect the homeowner's long-run satisfaction with the purchase. Top-quality, high-efficiency equipment will cost more initially, but it will save you money on utility bills and service calls for years to come. Contact Taylor's Heating, Air Conditioning & Refrigeration to find out more about how we can help you make the right choice.